FAQ on Rooftop Solar Installation & Mounting
Can I buy directly from Quick Mount PV?
Quick Mount PV products are sold to installers, contractors, electricians, roofers and other trade professionals exclusively through our distribution network. If you are an installer and would like to see Quick Mount PV products become available through your preferred distributor, let us know at . If you are a home or business owner who would like to make sure your solar installer uses Quick Mount PV products, be sure to tell them about us!
Are Quick Mount PV flashed mounts compatible with all rails?
Quick Mount PV flashed mounts are designed to work with almost all standard racking systems. Any rail that uses standard L brackets will work nicely with our flashed mounts and for systems that use slotted L feet will also allow for vertical adjustments within the L foot to compensate for roof dips and slopes. Lower profile rails such as Unistrut and ProSolar can also be used with Quick Mount PV flashed mounts. Here are a few of the racking systems that work with Quick Mount PV products:
- Conergy SunTop
- DPW Power Rail
- IWM Flushmount
- PV Racking, LLC
- SolarWorld Sunfix plus
- Zep Solar
If any of the racking systems you're interested in are not listed here, call our office or email and we will help you determine if it is compatible with Quick Mount PV products.
How long do Quick Mount PV flashed mounts last?
SMACNA (Sheet Metal and Air-conditioning Contractors National Association) sheet metal guidelines rate aluminum components for a lifespan of 50 years and stainless steel for 100 years. SMACNA requires .032" of thickness when aluminum or stainless flashing is used on a roof. Quick Mount PV Classic Comp Mounts (all in one flashing and mounts) are .050" thick. Top flashings for our QBase mounts and the underlayment flashings for our tile mounts are .032" thick. All included hardware is selected for durability and strength. For longevity, all exposed hardware is corrosion-resistant stainless steel; the QBase's 5/16-inch grade 8 lags were chosen for their greater tensile and shear strength. For durability the lags are shielded from corrosive moisture by a spun aluminum cone flashing. That's why all Quick Mount PV flashed mounts are projected to last at least as long as the PV system and most roofs. Quick Mount PV flashed mounts use EPDM rubber, the roofing industry standard for UV resistance and durability, everywhere a watertight seal is required.
Why do Quick Mount PV flashed mounts cost more than the competition?
Quick Mount PV flashed mounts are the best, most cost-effective code-compliant roof mounts available. Compare using Quick Mount PV flashed mounts to the overall cost of flashings, hardware, and installation time required by others on the market. Our Classic Composition mounts require no roof cutting, take only a minute to install and are designed to last 50 years. Many other mounts can take upwards of 10-20 minutes to install.
Taking into account the total cost for materials and installation time, Quick Mount PV flashed mounts can actually be more cost-effective than other mounts. Be sure to check carefully, as many manufacturers do not include flashing and basic hardware, which you have to purchase separately at additional time and expense. All Quick Mount PV flashed mounts for steep slope residential roofs include code-compliant flashings and all the hardware you need to attach the mounts to the roof and the racking to the mount. Our flashings and mounts are all aluminum with a 50-year lifespan, our flashings are larger and thicker than our competitors’, all exposed hardware is stainless steel, and the rubber seals and counter flashings are high-quality EPDM rubber.
How do Quick Mount PV flashings compare to the competition in building code-compliance?
Our pre-flashed and flashing-equipped products are completely waterproof and code-compliant and will not void a roof's warranty when applied according to the instructions given by Quick Mount PV and the roof manufacturer. Many other products on the market for roof penetration mounts are not code-compliant and/or will void a roof's warranty. Quick Mount PV has done extensive research on the various building authorities and industry groups that govern the way rooftop waterproofing should be done.
Each authority calls for the roof penetration to be flashed with the proper size and type of flashing. Many of the mounts on the steep-slope, residential market provide no flashing at all. Those that do are often too small to meet code. Retrofits can be challenging, as many flashing designs require cutting shingles to properly install the mount, which can void roof warranties. Also other mounts that are all-in-one flashing and mounts are not thick enough to withstand the point load of the mount and are susceptible to “potato chipping” (compression deflection or bending) that reduces the effective side lap protection against wicking and wind-driven rain. Our Classic Comp mount is completely code-compliant precisely because it has been designed both with building codes and roof warranties in mind.
Can I get longer hanger bolts for the Classic Composition and Shake Mounts?
Yes, we also stock 8-inch, 10-inch and 12-inch hanger bolts to replace the standard 5/16" x 6" bolts, in cases where you've got to penetrate a layer of insulation before reaching the rafters. Note that the longer hanger bolts are only longer in the shank portion of the bolts. The wood thread (bottom) end remains 3 inches and the machine threaded (top) end is 1.25 inches.
Where can I get engineering reports for Quick Mount PV products?
Engineering reports for both shear and pullout strength for Classic Comp and Shake, QBase Comp, QBase Low Slope, QBase Universal Tile, and Specialty Flat Tile mounts are available for download here at http://www.quickmountpv.com/support/downloads.html. Provide these reports to design engineers and the local building department when required. Installation guides for all our mounts also feature quick reference tables listing the allowable loads for structural attachments. If you need more documentation, or additional technical support, please call Tech Support at 925-478-8269 or email .
Where do I find installation and specification documents?
They can be downloaded here.
Will my building department recognize Quick Mount PV products?
Quick Mount PV products are recognized and welcome in jurisdictions all around the U.S., though not everyone has discovered us just yet. We provide downloadable engineering reports for each of our products documenting vertical pullout strength and shear, to address any of your local building department's concerns. Our installation instructions are thorough and should answer any questions about the installation process. If your building department has any additional concerns we are always happy to contact them on our customers' behalf.
All of our pre-flashed and flashing-equipped products meet or exceed U.S. and international requirements for waterproofing. All Quick Mount PV products exceed requirements for pullout and shear strength when used as directed. It is always a good idea to have your project approved before you get started. Take all applicable data to the building department for approval.
How do I install into LVL (laminated veneer lumber)?
Treat LVL just as if it were a rafter as long as the dimensions are consistent with conventional rafters: find the center, drill the pilot hole and drive in the hanger bolt.
Can Quick Mount PV be used on metal roofs?
No. Currently Quick Mount PV does not manufacture mounting products for metal roofs. For tips and suggestions email our tech department at .
Does Quick Mount PV have solutions for metal shingle roofing like Decra & Gerard?
Yes! We have products and solutions that work for almost all the common metal shingle profiles and manufacturers. We are currently finalizing instructions so stay tuned for the upcoming product release. In the meantime please get in touch with our tech department at and we’ll make sure you get everything you need to install strong, waterproof, 100% code-compliant mounts on your metal shingle roofs.
Do Quick Mount PV flashed mounts work on slate roofs?
Yes! While many solar integrators avoid slate roofs they are actually well suited for solar because slate roofs have a very long lifespan. Our QBase Shake and Slate Mount is the perfect mount for slate roofs. The mount transfers the loads from the solar array directly to the building structure so no unintended loads are placed on the slate, which would cause damage and leaks. Remember, slate is more difficult to walk and work on, so it may be best to work with an experienced slate roofer for installation of a PV system.
What if the flat tiles are not the standard 12" x 17"?
Our QBase Universal Tile Mount is an excellent option. It has a big, 18" x 18" flashing that's .032" thick, so it's strong but malleable. It employs a double-flash system to waterproof at the tile and deck (sheathing) levels. Follow the instructions in the Universal Tile Mount installation manual.
What if I can't use your Specialty Flat Tile Mount because the local building department has told me every mount must be bolted to a rafter?
We recommend always blocking (installing 4x4 wood blocks horizontally between rafters) the mount whenever it cannot be anchored directly to the center of a rafter (truss). OSB and plywood substrates do not provide the pullout strength required to withstand extreme conditions. If you have access to the inside of the roof and can add solid blocking, you can still use the Specialty Flat Tile Mount. If you cannot provide solid blocking, it is better to use the Quick Mount PV QBase Universal Tile Mount. Follow the instructions in the QBase Universal Tile Mount installation manual. Center the QBase over the rafter (truss) and secure it with the two 3" lags included with each mount kit. The QBase and 6.5-inch aluminum post have been tested to 3857 lbs. average pullout (Douglas fir) and 775 lbs. average shear.
Do Quick Mount PV products work with solar thermal systems?
Of course! Our mounts are the strongest on the market, so naturally they're the best you can buy for mounting solar hot water on any steep slope, low slope, commercial or residential non-metal roof. Our QBase products – the QBase Comp, QBase Low Slope and QBase Universal Tile mounts – have the best shear strength available. And our Classic Comp and Shake mounts can be beefed up for hot water by replacing the standard 5/16-inch diameter hanger bolt with a thicker 3/8-inch bolt when required by local code, however, the 5/16-inch hanger bolt works just as well with solar thermal and has a similar pullout rating.
Can I use Quick Mount PV products to support other equipment on roofs?
Our mounts also work as a waterproof, reliable solution for satellite dishes, air conditioning and electrical conduit. We can also design a custom solution for any need our standard products don't address.
How many mounts should I install per module?
The number typically calculates to 1-2 mounts per module, however the number and spacing of the mounts must be determined by a qualified designer using engineering reports and calculations that properly configure the mounting system to handle wind, snow, seismic, and array loads and with consideration of the roof structure and integrity. The number of mounts per module will vary from job to job, as no two sites are alike. Quick Mount PV provides engineering reports for pullout and shear.
How do I calculate for externally applied loads (wind, snow, seismic)?
The proper calculations will depend upon many variables and considerations. Each system designer will need to complete the calculations based on variables unique to each job. Determining the spacing between mounts depends upon the strength of the rail, the distance between parallel rails, the amount of cantilever where the modules overhang the rails, the pullout strength of the mount, the slope of the roof, wind exposure, the wind zone and roof type, the structural integrity of the roof framing, and more. We can provide structural test reports on all of our mounts, as needed. Commonly a licensed installer can answer these questions. If s/he can't then s/he will need to find somebody who can. A licensed engineer is the best solution.
Should I re-roof before installing a PV system?
This depends on the remaining life of the existing roof. Unless the roof is within a few years old it is likely that it will need to be replaced during the life of the array. To do this it will be necessary to decommission, remove and reinstall the array. This can be an expensive endeavor. You need to find a balance between the increased cost of re-roofing now and the additional cost of removing and reinstalling the array to re-roof later. One compromise is to re-roof the area with the array now and the rest of the roof later.
Which should I choose; aluminum mounts with a mill finish or anodized aluminum?
We offer our mounts in three finishes: Mill Finish, Clear Anodized, & Bronze Anodized (Black). The anodized finishes cost more, but are often favored for aesthetic reasons, because they visually blend more easily into the roof color. Another benefit of anodizing is added corrosion resistance in coastal areas with high salt content in the air, mostly within 1-2 miles of the ocean. Industrial areas can be more corrosive environments as well.
How high off the roof are the modules with the Quick Mount PV Classic Composition Mount?
Our mounting block is 1.25 inches tall. Using an L foot and a rail typically will add 2 to 4 more inches plus the depth of the module frame. This allows for the commonly recommended minimum 4" spacing between the roof and the module frame to promote convective cooling of the PV array on most pitched roofs. Proper convective cooling design keeps temperature as low as possible for increased kWh production and longer module life. The array height can easily be increased with our height extensions, available in 2.5-inch, 3.25-inch and 4-inch lengths. Strut-style rails like ProSolar and Unistrut rails do not utilize an L foot, making their typical height 3 inches off the roof, which is why extensions might be considered, especially in hotter climates.
How do I raise the modules higher off the roof while using the Classic Comp Mount?
Quick Mount PV offers height extensions in three different lengths: 2.5-inch, 3.25-inch and 4-inch. These bolt directly to the QBlock in our Classic mounts to raise the array if desired.
How do I keep from voiding a roof's warranty?
The manufacturer's instructions will spell out exactly what does and does not void the warranty of their roofing product. Officially, the roofing manufacturer's instructions supersede our instructions, as our mounts are integrating with their roofing system.
On a roof with a material and labor warranty in place, it is strongly recommended to consult the roofer of record. Often the roofing contractor will void the labor portion of their warranty if someone from another trade modifies their work. Give the roofing contractor the option of handling the roofing modifications, or at least give them the opportunity to inspect and approve the modifications you make. There may be fees to this roofer, but if it maintains the labor warranty, it should be money well spent.
Do a thorough roof evaluation before beginning work. Take photos of important roof features and determine the quality of the roofing so any repairs or replacement can happen before or in conjunction with the installation. On a composition/asphalt shingle roof it is important to know as much as possible about who manufactured the materials, the age of the roof, the type of substrate (plywood or oriented strand board [OSB]), the rafter size, spacing and span, the age of roof structure, who built the home and who roofed it.
Often the building owner will have the name of the composition manufacturer on file. If not, take a piece of the roof material to a roofing yard; they can usually recognize the maker and its approximate age. Tile roof manufacturers put a stamp of some sort on the back of each tile. This mark can be identified by the roofing yard, or by doing research via the Internet. Once you know the manufacturer, it should be easy to obtain their written installation instructions.
The manufacturer's instructions will spell out exactly what does and does not void the warranty of their roofing product. Most have a clause about a recommended range of rooftop temperatures appropriate for installing the roof. This is commonly missed, but can easily be noted if you read the instructions. It is also important to have manufacturer instructions in the job file, for future reference. If no manufacturer can be found, there is likely no warranty in place.
What is the best method for locating rafters?
This is a common question. Unfortunately, because there are many types of roofs and considerable variation in construction, there is no one right answer. Rafters should be spaced 16 or 24 inches on center but, once you get on the roof you'll find that structures shift and settle, designs and installations change, and remodels or additions happen, so it's best to assume that no two roofs will be the same.
There are a few tricks for finding the exact location of the center of the rafter. First, you will want to find out as much as possible about the roof before you begin your installation (read the "Know Your Roof" section in the Quick Mount PV installation guide for each product).
One of the easiest and most common methods is to look at the overhang of the roof. When the ends of the rafters are visible, it's possible to project the course of the rafters up the roof from there. Use a chalk line to mark the rafter location.
Another is to locate an eyebrow vent on the roof and measure off its center equally in both directions. It is also possible to find rafters using a “deep wall scan tool”. During frosty conditions the rafter's perimeters will be visible from the roof.
Climbing into the attic space reveals the structural layout from the inside, so you can see exactly where the rafters are. Map the rafter locations by measuring the base, center, and top of each rafter and transfer this map to the surface of the roof. One way to transfer locations from below to on top of the roof is to drill a hole adjacent to a rafter and then measure over ½ the width of the rafter.
Will any sealant do?
No. It is important to use a sealant compatible with all the materials it will contact. Most roofing manufacturers have a suggested or approved roofing sealant that is compatible with their roofing type. Using a sealant that is not approved by the roofing manufacturer can void the manufacturer’s warranty. Geocel 4500, Chemlink M1, Solar Seal 900 are three examples of several good sealants with adhesive properties that are compatible with composition shingles, metals, wood and EPDM Rubber. In the freeze-thaw zones, it is important to follow the manufacturer's guidelines for freeze-thaw conditions.
In the past installers have counted on Sikaflex as a universal sealant. The specifications of Sikaflex 1A, however, state: "Do not use in contact with bituminous/asphaltic materials."
It is very important to use the roofing manufacturer's suggested/recommended/approved sealants. Using the wrong sealant may cause a chemical reaction to break down your sealant or the roofing material faster than its stated lifespan, risking water intrusion. The more you know about the roof you are working with the more you can respect its properties to insure high quality, watertight mounting systems.
Is it possible to apply too much sealant?
Yes. It is required to put sealant in the pilot hole prior to driving the hanger bolt and our QBase Mounts also use sealant where the flashing meets the post. Some people put a bead of sealant on the bottom of the flashing in a horseshoe shape about four inches across with the open end on the low side of the roof. This should be the extent of any extra sealant, as we still want the flashing to float with the expansion and contraction of the roofing materials, as it was intended.
What are the torque specifications for the Classic Comp Mount?
The best way to establish proper torque is to grasp the QBlock while tightening the mounting bolt and lightly rotate the block back and forth while tightening the mounting bolt. Stop tightening as soon as the QBlock stops rotating. Ideally, the QBlock should be oriented at a 45 degree angle to promote water drainage.
Can I mount directly to an I-joist?
No. While some manufacturers and engineers may allow this, we strongly recommend installation of solid blocking between the I-joists and then mounting to the blocking. Bolting directly to the top of an I-joist may cause damage to the I-joist and risks inconsistent and potentially inadequate pullout strength. Be sure to follow the I-joist manufacturer's instructions.
How do I remove Quick Mounts from a composition/asphalt shingle roof?
There are two methods of removal:
1. If you are temporarily removing the PV system to re-roof and reinstall in the same location, just remove the nuts and washers at the top of the mount to allow removal of the flashing. Leave the hanger bolts in place and reassemble the new roofing around them before reinstalling the PV arrays.
2. If you need to remove the hanger bolts, lock two nuts together at the top of the hanger bolt, then use a half-inch open-end wrench on the bottom nut to back the hanger bolt out. Unlock the two nuts and reuse them. It's also possible to use a heavy nut on the bottom (5/16" nut x 9/16" hex), locked to a normal nut on top (5/16" nut x ½" hex). Then, a deep 9/16" socket will span over the 1/2" hex, and you can spin them out quickly with a cordless gun.
Watch our Quick Tips ~ Bolt Removal for The Classic Comp Mount video for more info.
Are Quick Mount PV trainings available?
Yes. We are now offering industry leading educational opportunities at our Solar Roofing Training Center at our Northern California headquarters. Also, Quick Mount PV training sessions are often available through webinars, or PowerPoint and hands-on presentations offered at distributor dealer trainings, trade shows, as a part of PV and thermal installation classes, and in conjunction with other training organizations. For a list of upcoming trainings and events you can visit our training & events page, and/or email .
Do flashings need to be grounded?
Flashings (or any other exposed metal surfaces) do not need to be grounded as long as the PV system meets the following criteria:
1. The PV system must be a "non-separately derived system" i.e. grid tie or grid tie battery backup system - Off grid (stand alone system) flashings and other exposed metal surfaces may require bonding to ground.
2. The PV system must have a "defined" ground path - If you use a ground wire connected directly to module frames with outdoor rated grounding lugs, there is no problem defining the ground path, but if you use grounding washers with piercing teeth or other piercing type bonding hardware that bond the module frames to ground through the racking system, you must define the bonding and grounding path in the plans and have clearly-visible, permanent labeling of the bonding and grounding path.
3. The PV cables must be routed in a way that prevents contact with "accessories" (flashings, array skirts, wind deflectors, wire management clips, and mid/end clamps) in the event of failure. This may necessitate wire to be clipped securely to the modules frames as regular intervals or contained in conduit, wire raceways, or inside the racking system rail (like inside a strut style rail). It is recommended that the wires not be able to be pulled out of the raceway if they are accidentally cut.